KILZ® PVA DRYWALL PRIMER Professional Interior Primer | KILZ®

KILZ® PVA DRYWALL Professional Interior Primer

Avg. Rating:

KILZ PVA DRYWALL PRIMER is designed for use on new drywall. It is a fast-drying, interior water-based primer formulated to prime and seal new, uncoated drywall and reduce the number of topcoats required to achieve a uniform, professional quality finish.

 

Designed for use under flat and low sheen paints only. Do not topcoat with glossy paint finishes.

Seals Porous Surface

Available in 3.79 L and 18.93 L sizes

Please check availability before visiting your local retailer.


KEY FEATURES

For use on new uncoated drywall. Seals porous drywall to achieve a uniform, professional quality finish in less coats. Fast drying, Low VOC, ready to spray, brush or roll. Easy soap and water clean-up. Greenguard Gold Certified.

BEST FOR USE ON

Interior use. Use on new, bare and uncoated drywall, gypsum and some types of plaster.

COVERAGE

300 to 400 sq ft/gal

TECHNICAL DOCUMENTS

PRODUCT USAGE

The following steps are recommended for product performance.

  • Cover all nail and screw heads with joint compound according to directions and sand to smooth surface.*

  • Tape drywall and apply joint compound. Allow to fully cure according to directions prior to priming.

  • Sand to smooth surface before priming.* Wipe off dust with a damp cloth. Allow to dry thoroughly.

*WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.

Application

  • Eye protection is recommended.

  • Use only when temperatures are between 50°F (10°C) and 90°F (32°C).

  • Coverage is approximately 28 – 37 m2 (300-400 sq. ft.) per 3.79 L depending on surface porosity.

  • For airless spray applications, tip size should be .017"-.021" tip/60 mesh filter.

  • May be tinted with up to 60 ml of universal colourant per 3.79 L container.

  • Glossy Surfaces: Not recommended. Please use KILZ® PREMIUM or KILZ 2® Primers.

  • Masonry, Brick, Stucco and Plaster: Not recommended. Please use KILZ® PREMIUM or KILZ 2® Primers.

  • Stainblocking: Not formulated to block stains - For stainblocking, use oil based primers like KILZ® ORIGINAL and water based primers like KILZ 2® or KILZ® PREMIUM.

Read More

Dry Time at 77°F (25°C), 50% RH

  • Dries to the touch in 30 minutes.

  • Paint or topcoat after 2 hours.

  • Application at lower temperatures, in high humidity or in poorly ventilated areas will affect dry time.

Read More

Clean-Up & Disposal

  • Use soap and water to clean hands, tools, and spills.

  • For recycling or disposal of empty containers and unused product, contact your household refuse collection service.

Read More

Read More

WARRANTY
LIFETIME LIMITED WARRANTY

Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: [email protected]. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Warning!

This product contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.
 


 

USE ONLY WITH ADEQUATE VENTILATION

Warning! Irritant!

CAUTION IRRITANT Avoid contact with eyes. May cause eye, nose and throat irritation. Avoid breathing of dust, vapors or spray mist. Open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/ mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC -23C or equivalent) during and after application. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling and before smoking or eating.

Warning!

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.



First Aid

If swallowed, do not induce vomiting. Get medical attention immediately. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.

KEEP FROM FREEZING. If frozen, let thaw at room temperature. 

KEEP OUT OF REACH OF CHILDREN

Read More

PRODUCT SPECIFICATIONS

  • Base

    Water

  • Int/Ext

    Interior

  • Colour

    White

  • Coverage - Low

    28 m2 (250 sq. ft.)

  • Mils Wet

    6.4

  • Mils Dry

    1.7

  • Coverage High

    37 m2 (400 sq. ft.)

  • Mils Wet

    4.0

  • Mils Dry

    1.0

  • Finish @ 85°

    < 10

  • Min Application Temp

    50°F (10°C)

  • Max Application Temp

    90°F (32°C)

  • Viscosity

    105 - 115 KU

  • Dry To Touch

    30 min

  • Dry To Recoat

    2 hour

  • Max Tint

    59 ml

  • VOC

    <100 g/L

  • Brush

    Nylon / Polyester Blend

  • Roller - Smooth

    10-13 mm nap

  • Roller - Porous

    13-19 mm nap

  • Spray Tip

    .015" - .021"

  • Spray Filter

    60 mesh

  • Spray Pressure

    2,500 - 3,000

  • Volume Solids

    27% (+/-) 2%

  • Weight Solids

    42% (+/-) 2%

  • Flashpoint

    N/A

paint brush

CONNECT WITH US

Be the first to know about new products, contests, our latest promotions and more.