KILZ® MOLD & MILDEW
Interior | Exterior Primer
All New KILZ® MOLD & MILDEW Primer is a water-based primer-sealer-stain blocker that offers excellent adhesion to both interior and exterior surfaces and provides a sound anchor for paints. The EPA registered active ingredient creates a mold and mildew-resistant film that protects the primer film from mold and mildew growth. KILZ MOLD & MILDEW Primer will block most medium to heavy stains including felt marker, grease, ink, pencil, tannin and water stains. It is a fast-drying, low odour, very low VOC formula and is easy to clean with soap and water.
Seals Porous Surface
Promotes Adhesion
Hides Previous Color
Mildew Resistant Finish
Helps Block Medium/Heavy Stains
KEY FEATURES
High hide, Heavy duty stain blocker, Exceptional adhesion, Mildew resistant, Contains EPA-registered mildewcide, Prevents mold & mildew growth on the primer film, Very low VOC, Seals porous surfaces, Greenguard Gold Certified
BEST FOR USE ON
Interior and exterior surfaces. Surfaces that needs more hiding power, tougher and heavier stains and when more adhesion performance is needed. Multi-purpose priming for walls, trim, doors and cabinets, Apply to drywall, plaster, wood, brick, masonry, concrete, cinder block, masonry, stucco, galvanized steel, aluminum, PVC, plastic, vinyl, properly prepared glossy surfaces.
COVERAGE
28 - 37 m² per 3.79 L
TECHNICAL DOCUMENTS
The following steps are recommended for product performance.
- Eye protection is recommended. For spray applications, a small amount of water (no more than 15 ml per 3.79 L)) may be added.
- If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry.
- Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface.
- Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.*
- †Mold or Mildew Covered Surfaces: This product is designed to prevent mold and/or mildew from forming and contaminating the primer film before topcoat is applied. Although it is designed to be applied directly to mold and mildew prone surfaces, any existing mold and/or mildew on the surface should be removed before priming and painting. This will ensure best results. Wash the area with a mildew remover, rinse with water and allow to dry before priming.
- Masonry, Brick and Plaster: KILZ MOLD & MILDEW Primer may be used on clean, dry, aged masonry surfaces. New masonry must be allowed to cure (dry) at least 30 days before applying KILZ MOLD & MILDEW Primer.
- Fire Restoration: Not recommended. Primer Recommendations: KILZ® ORIGINAL, KILZ® ORIGINAL INTERIOR/EXTERIOR and KILZ® RESTORATION.
*WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
- Eye protection is recommended. For spray applications, a small amount of water (no more than 15 ml per 3.79 L)) may be added.
- Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C). Stir thoroughly before and occasionally during use. Apply using a brush, roller or sprayer.
- Brush – High quality Nylon/Polyester.
- Roller – High quality 10 - 13 mm nap on smooth surfaces or 13 - 19 mm nap on semi-rough or porous surfaces.
- Airless spray – .017-.021" tip / 60 mesh filter.
- Prime the entire surface to ensure a uniform appearance of the topcoat.
- Stainblocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating.
- Tinting: KILZ MOLD & MILDEW Primer may be tinted with up to 2 ounces of universal colourant per gallon. Tinting to a lighter shade than the topcoat is recommended.
- Coverage: 300-400 sq. ft. (27.87-37 m2) per gallon depending on application method and surface porosity.
Read More
Dry Time at 77°F (25°C), 50% RH
- Dries to the touch in 30 minutes.
- Recoat or topcoat after 1 hour.
Read More
Clean-Up & Disposal
- Clean equipment and paint spatters with warm, soapy water.
- Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.
- If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal information contact your local household refuse collection service.
Read More
Read More
WARRANTY
LIFETIME LIMITED WARRANTY
Masterchem Industries LLC warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for so long as you reside in your home. If this product is found to be defective upon inspection by its representative, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty is not transferable. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To the extent permitted by applicable law, any implied warranties including the implied warranties of merchantability and of fitness for a particular purpose, are limited to the duration of this express warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. For warranty service, call: 1-866-774-6371, or email: [email protected]. Masterchem Industries LLC reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
†Warning!
This product contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.
USE ONLY WITH ADEQUATE VENTILATION
Warning! Irritant!
CAUTION IRRITANT Avoid contact with eyes. May cause eye, nose and throat irritation. Avoid breathing of dust, vapors or spray mist. Open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/ mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC -23C or equivalent) during and after application. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling and before smoking or eating.
†Warning!
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
First Aid
If swallowed, do not induce vomiting. Get medical attention immediately. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.
KEEP FROM FREEZING. If frozen, let thaw at room temperature.
KEEP OUT OF REACH OF CHILDREN
Read More
PRODUCT SPECIFICATIONS
Base
Water
Int/Ext
Int/Ext
Colour
White
Coverage - Low
28 m2 (300 sq. ft.)
Mils Wet
5.3
Mils Dry
2.2
Coverage High
37 m2 (400 sq. ft.)
Mils Wet
4
Mils Dry
1.7
Finish @ 85°
< 10
Min Application Temp
50°F (10°C)
Max Application Temp
90°F (32°C)
Viscosity
95 - 105 KU
Dry To Touch
30 min
Dry To Recoat
1 hour
Max Tint
60 mL per 3.79L / 15 mL per 946 mL / 300 mL per 18.93 L
VOC
<5 g/L
Brush
Nylon / Poly
Roller - Smooth
10 -13 mm nap
Roller - Porous
13 - 19 mm nap
Spray Tip
.017" - .021"
Spray Filter
60 mesh
Spray Pressure
2,500 - 3,000
Volume Solids
42% (+/-) 2%
Weight Solids
55% (+/-) 2%
Flashpoint
N/A
