KILZ 1® STANDARD
Interior Primer
KILZ® 1 STANDARD Primer is designed for use on multiple interior surfaces helping save cost by reducing the number of coats of paint needed to achieve optimal results. It seals porous surfaces, hides minor scuffs and marks and promotes a more uniform appearance of the topcoat. It’s ready to brush, roll or spray and can be topcoated after 1 hour with water or oil-based paint.
Use KILZ 1 STANDARD Primer on almost all interior surfaces including wood, drywall, plaster, brick, masonry and more. Not recommended for flooring, glossy surfaces, mold and mildew prone surfaces or for stainblocking.
Seals Porous Surface
Promotes Adhesion
Available in 946 mL, 3.79 L & 18.9 L sizes
Please check availability before visiting your local retailer.
KEY FEATURES
Low cost primer for interior multi-surface use. Seals porous surfaces, hides light scuffs, marks and blemishes, prevents joint/seal flashing, low odour, fast drying and easy soap and water clean-up. Helps improve topcoat uniformity and appearance. Greenguard Gold Certified.
BEST FOR USE ON
Interior use. Use on drywall, plywood, brick, concrete, masonry and paneling.
Coverage
28-37 m² (300-400 sq. ft.) per 3.79 L
TECHNICAL DOCUMENTS
- All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose peeling paint, rust and all other foreign substances.
- If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry.
- Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.*
- Glossy Surfaces: KILZ 3® PREMIUM and KILZ 2® Primers are recommended for use over properly prepared glossy surfaces.
- Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
- Note: KILZ 3® PREMIUM and KILZ 2® Primers are recommended for mildew-prone surfaces.
- Masonry, Brick, Stucco and Plaster: KILZ 1 STANDARD Primer may be used on clean, dry, aged masonry surfaces. New masonry must be allowed to cure (dry) at least 30 days before applying KILZ 1 STANDARD Primer.
*WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National Lead Information Center at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
- Eye protection is recommended. For spray applications, a small amount of water (no more than ½ pint per gallon) may be added.
- Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C). Stir thoroughly before and occasionally during use.
- Apply using a brush, roller or sprayer.
- Brush – High quality Nylon/Polyester
- Roller – High quality 10 - 13 mm nap on smooth surfaces or 13 - 19 mm nap on semi-rough or porous surfaces.
- Airless spray – .017 - .021 tip / 60 mesh filter
- Prime the entire surface to ensure a uniform appearance of the topcoat.
- Stainblocking: Important - For stainblocking, use oil based primers such as KILZ ORIGINAL or water based primers such as KILZ PREMIUM.
- Tinting: KILZ STANDARD Primer may be tinted with up to 60 ml of universal colourant per 3.79 L container. Tinting to a lighter shade than the topcoat is recommended.
- Coverage: 300 - 400 sq. ft.(28 - 37 m2) per gallon depending on application method and surface porosity.
Read More
Dry Time at 77°F (25°C), 50% RH
- Touch in 30 minutes.
- Paint in 1 hour.
- Low temperatures, high humidity or poor ventilation can significantly increase dry and paint application times.
Read More
Clean Up & Disposal
- Clean equipment and paint spatters with warm, soapy water. If spilled, contain material and remove with an inert absorbent.
- Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.
- Do not dispose of this product down a drain. Please consider donating any unused product.
- For recycling or disposal information contact your local household refuse collection service.
WARNINGS
MAY IRRITATE EYES AND SKIN. Avoid contact with eyes, skin and clothing. Do not breathe fumes. Keep out of reach of children. Wear eye protection and protective clothing. Use only with adequate ventilation.
FIRST AID TREATMENT: Contains: TITANIUM DIOXIDE, KAOLIN, CALCIUM CARBONATE, ACRYLIC POLYMER AND NEPHELINE SYENITE. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15-20 minutes. If on skin, rinse well with water. If inhaled, move person to fresh air.
Read More
Read More
PRODUCT SPECIFICATIONS
Base
Water
Int/Ext
Interior
Colour
White
Coverage - Low
28-37 m² (300-400 sq. ft.) per 3.79 L
Mils Wet
6.0
Mils Dry
1.2
Coverage High
28-37 m² (300-400 sq. ft.) per 3.79 L
Mils Wet
4.0
Mils Dry
0.8
Sheen
<10.0 @ 85°
Min Application Temp
10°C (50°F)
Max Application Temp
32°C (90°F)
Viscosity
90 - 100 KU
Dry To Touch
30 min
Dry To Recoat
1 hour
Max Tint
15 ml per 3.79 L
VOC
<100 g/L
Brush
Nylon / Poly
Roller-Smooth
10-13 mm nap
Roller-Porous
13-19 mm nap
Spray Tip
.017" - .021"
Spray Filter
60 mesh
Spray Pressure
1,800 - 3,000
Volume Solids
20% (+/-) 2%
Weight Solids
35% (+/-) 2%
Flashpoint
N/A
